Supercoat Base & Render Coats

Supercoat™ Acrylic Flexibase

Supercoat™ Flexibase is a thick, high build Acrylic base coat which can be used as a base coating on residential, commercial/industrial buildings, fences and sound barriers. It is ideal for float coats of up to 4mm (typically 2 - 4mm) and in most circumstances is fully meshed. It is highly flexible and therefore suitable in crack prone areas. Supercoat™ Flexibase can be trowelled, pumped or roller applied to the wall. This product is ideally suited for use over flat substrates and is a high quality cost effective solution developed using Long Life Protective Coating Technologies.

 

Supercoat™ Superbuild Render

This render is highly modified with polymers and is ideal for flat coats of up to a 6mm thickness (typically 3 - 6mm) but is potentially capable of much greater builds. The high content of additives alleviate suction issues over many substrates so that the substrate would not have to be sealed using Supercoat™ Surface Sealer prior to application. It is designed as the first layer into which Supercoat™ Grid Mesh can be pressed. The additives in this mix give the render great build capabilities, workability, elasticity and spreading characteristics off the trowel. Water entraining chemicals allow it to remain wet enough to take the reinforcement, even after the Applicator has taken some time to cover enough wall to receive a full height sheet of grid mesh. Adding Supercoat™ Renderbond will improve performance even further.

 

Supercoat™ Superbase Render

This render is a quality, cost effective product designed for a premium finish on a tight budget. It is ideal for float coats of up to 4mm thickness (typically 2 - 4mm). This product becomes a high quality cost effective solution when the substrate does not have to be sealed prior to application. It is designed as the first layer into which Supercoat™ Grid Mesh can be pressed. The Supercoat™ Superbase Render still has good workability, elasticity and spreading characteristics off the trowel. Water entraining chemicals allow it to remain wet enough to take the reinforcement, even after the Applicator has taken some time to cover enough wall to receive a full height sheet of grid mesh. Adding Supercoat™ Renderbond will improve performance even further.

 

Supercoat™ Multitex

Supercoat™ Multitex is a graded sand, white cement, high grade lime supplement and additive, dry mixed product, designed as a super strong adhesion plaster to provide an etching key coat for subsequent Supercoat™ render based products.

 

Its scope consists of;

 

- Adhering of EPS (expanded polystyrene) or keyed XPS (extruded polystyrene) to solid substrates.

- Utilised as a key coat over smooth surfaces such as previously painted or smooth substrates.

- Can be applied with glass fibre mesh as a mesh coat or reinforcement in difficult areas.

- Mixed as a slurry, applied to PVC (polyvinyl chloride) components to be plastered or coated.

- As a key coat over Clay Brick, Tilt Slab, Concrete Block, Solid Fibre Cement sheet, keyed XPS (extruded polystyrene) and EPS (expanded polystyrene) substrates.

 

Supercoat™ Superskim Render

Supercoat™ Superskim Render has been specifically designed as a high quality, graded, fine sand mix with good adhesion, spreading and workability. Supercoat™ Superskim Render is designed for tight 1 - 4mm intermediary mesh covering skim coats and must be applied after the base mesh carrying coat has dried. Supercoat™ Skimbond is added for additional polypropylene fibre reinforcement and water entrainers for additional workability and elasticity in varying climatic conditions. Supercoat™ Superskim Render is a far smoother, more flexible skim finish than the general purpose Supercoat™ Superbuild or Supercoat™ Superbase Render products.

 

 
 
 





Supercoat Flexibase






Supercoat Bag